Lipid monolayer as a simple model membrane for comparative assessment of the photodynamic therapy photosensitizer efficiency via macroscopic measurements.

Cellular membrane is one of the main targets of photodynamic therapy. Its high complexity has led to the study of the efficiency of photosensitizers on artificial lipid systems mimicking membranes. However, the preliminary analysis of this efficiency remains limited due to difficulty of the model construction and/or implementation of the required measurement techniques. Hereby, we propose a quite simple way for the rapid comparative assessment of novel photosensitizers in terms of membrane photodegradation, based on simple and fast measurements, such as wetting angle and surface plasmon resonance spectroscopy. As a proof of concept, we applied this methodology to two bacteriopurpurinimide derivatives. We have shown in particular that such complementary techniques can be employed not only for the multiparametric monitoring of the kinetics of the photodegradation, but also for the comparison of the damaging efficiency of the photosensitizers in the lipid structures as well.

Hydrocalumite Thin Films for Polyphenol Biosensor Elaboration.

Hybrid thin films based on Hydrocalumite (Ca2AlCl layered double hydroxide LDH) and tyrosinaseenzyme have been used for the elaboration of a high sensitive amperometric biosensor detecting polyphenols extracted from green tea. Structural properties of LDH nanomaterials were characterized by X-ray powder diffraction and Infra-Red spectroscopy, confirming its crystalline phase and chemical composition. Ca2AlCl-LDHs-thin films were deposited by spin-coating, and studied by atomic force microscopy to obtain information about the surface morphology of this host matrix before and after enzyme's immobilization. Electrochemical study using cyclic voltammetry and chronoamperometry shows good performances of the built-in biosensor with a high sensitivity for polyphenols concentrations ranging from 24 pM to and a limit of detection of 1.2 pM.

Development of an Immunosensor Based on Layered Double Hydroxides for MMR Cancer Biomarker Detection.

As a potential biomarker for the investigation of cancer inflammatory profiles, macrophage mannose receptor (MMR, CD206) is herein selected to develop an immunosensor based on layered double hydroxide (LDH). Like an endocyte C-type lectin receptor, MMR plays an important role in immune homeostasis by scavenging unwanted mannose glycoproteins. It attracts a progressive attention thanks to its particularly high expression within the tumor microenvironment. There is a great of interest to develop an immunosensor based on an antibody specific to MMR for detection of stroma versus tumor cells. In this work, we studied the feasibility of high sensitive MMR cancer Screen Printed Electrode (SPE) immunosensor. Working electrode of commercialized SPE was modified by immobilization of specific antibody (anti-MMR) into thin layer of LDH nanomaterials. Structural, morphological, and surface properties of LDHs were studied by X-Ray diffraction, atomic force microscopy and Infrared spectroscopy in ATR. Cyclic Voltammetry technique was used to study interaction between the human recombinant MMR protein (rHu-MMR, NSO derived) and an immobilized antibody into developed immunosensor. High specific response of -11.72 µA/ng.mL(-1) (with a correlation coefficient of R(2)=0.994 ) were obtained in linear range of 0.05 ng/mL to 10.0 ng/mL of specific recombinant antigen. The limit of detection (LOD) was less than 15.0 pg/mL. From these attractive results, the feasibility of an electrochemical immunosensor for cancer was proved. Additional experiments to study stability and reproducibility the immunosensor should be completed in perspective to use these anti-MMR based immunosensors for sensing human MMR in patient biopsies and sera.

High sensitive mesoporous TiO2-coated love wave device for heavy metal detection.

This work deals with the design of a highly sensitive whole cell-based biosensor for heavy metal detection in liquid medium. The biosensor is constituted of a Love wave sensor coated with a polyelectrolyte multilayer (PEM). Escherichia coli bacteria are used as bioreceptors as their viscoelastic properties are influenced by toxic heavy metals. The acoustic sensor is constituted of a quartz substrate with interdigitated transducers and a SiO2 guiding layer. However, SiO2 shows some degradation when used in a saline medium. Mesoporous TiO2 presents good mechanical and chemical stability and offers a high active surface area. Then, the addition of a thin titania layer dip-coated onto the acoustic path of the sensor is proposed to overcome the silica degradation and to improve the mass effect sensitivity of the acoustic device. PEM and bacteria deposition, and heavy metal influence, are real time monitored through the resonance frequency variations of the acoustic device. The first polyelectrolyte layer is inserted through the titania mesoporosity, favouring rigid link of the PEM on the sensor and improving the device sensitivity. Also, the mesoporosity of surface increases the specific surface area which can be occupied and favors the formation of homogeneous PEM. It was found a frequency shift near -20±1 kHz for bacteria immobilization with titania film instead of -7±3 kHz with bare silica surface. The sensitivity is highlighted towards cadmium detection. Moreover, in this paper, particular attention is given to the immobilization of bacteria and to biosensor lifetime. Atomic Force Microscopy characterizations of the biosurface have been done for several weeks. They showed significant morphological differences depending on the bacterial life time. We noticed that the lifetime of the biosensor is longer in the case of using a mesoporous TiO2 layer.

Heterogeneous cell mechanical properties: an atomic force microscopy study.

Atomic force microscopy (AFM) is a non-invasive microscopy to explore living biological systems like cells in liquid environment. Thus AFM is an appropriate tool to investigate surface chemical modification and its influence on biological systems. In particular, control over biomaterial surface chemistry can result in a regulated cell response. This report investigates the influence of adhesive and non-adhesive surfaces on the cell morphology and the influence of the cytoskeleton structure on the local mechanical properties. In this study, the main work concerns a thorough investigation of the height images obtained with an AFM as therecorded images provide the evolution of the mechanical properties of the cell as function of its local structure. Information on the cell elasticity due to the cytoskeleton organization is deduced when comparing the AFM tip indentation depth versus the distance between the cytoskeleton bundles for the different samples.

Characterization of dynamic cellular adhesion of osteoblasts using atomic force microscopy.

BACKGROUND: Atomic force microscopy (AFM) can be used to visualize the cell morphology in an aqueous environment and in real time. It also allows the investigation of mechanical properties such as cell compliance as a function of cell attachment. This study characterized and evaluated osteoblast adhesion by AFM. METHODS: Human bone marrow stromal cells were cultured on two types of surface to induce weak and strong cellular adhesions. RESULTS: Cells were considered as spreading if they had a flattened and lengthened shape and a cytoskeletal organization in the submembrane cytosolic region. Cell detachment demonstrated different adhesion states between adherent cells to be distinguished. The stability of the cytoskeletal fibers indicated that cells were adherent. The elastic modulus was estimated by two complementary approaches. The values deduced were between 3 x 10(2) and 2 x 10(5) Nm(-2) according to the state of cell adhesion and the approaches used to measure this elastic modulus. CONCLUSIONS: Although the results were qualitative, a relation may be deduced between the elasticity of living cells as demonstrated by cytoskeletal organization and the state of cell adhesion. The technique could be used to determine the adhesion state of an adherent osteoblast observed under AFM.

Study of two grafting methods for obtaining a 3-aminopropyltriethoxysilane monolayer on silica surface.

In order to establish a 3-aminopropyltriethoxysilane (APTES) grafting procedure with limited number of APTESs noncovalently linked to the silica surface, two different methods of grafting (in acid-aqueous solution and in anhydrous solution) were compared. The grafted surface state was investigated by atomic force microscopy (AFM). The stability of the grafting was checked at different temperatures by AFM. Continuous and plane APTES grafted surfaces were successfully prepared using both grafting preparations. The grafting in an anhydrous solution behaves homogeneously and stably compared to the grafting in an acid-aqueous solution. Moreover, with anhydrous solution, results showed that a unique monolayer of APTES was grafted.